A home EV charger must go on its own circuit, and a registered electrician must install it. In Norway, only a registered electrical company may do this work, and every new charge point must be a permanently mounted charger, not a socket. The electrician fits the circuit and the earth-fault protection, checks the surge protection, tests the charger and documents the work. A standard job takes about half a day.

Why fit a dedicated home charger?

Because it is cheaper, faster and safer than the alternative, and because in most of Europe it is now the only compliant way to charge at home. A dedicated charger runs on its own circuit, charges three to ten times faster than a household socket, and is built to run at full load overnight without complaint. Home electricity on the right tariff also costs a fraction of public charging. The reasons not to rely on a socket, and what the safety rules actually say, are in our guide to charging from a regular socket.

What you need before installing

Check these points before you call an installer. They decide what you can fit and what it will cost, and knowing them saves time and a few awkward surprises.

  1. Your supply. Single-phase or three-phase. Single-phase caps a home charger at 7.4 kW, and a three-phase 400 V supply opens up 11 kW and 22 kW. Most homes in the UK are single-phase, and three-phase 400 V is common in Germany and much of the continent. Most Norwegian homes have a 230 V IT grid, where amina chargers charge on single-phase only, at up to 7.4 kW. Our guide to IT and TN grids explains the difference.
  2. Your available capacity. Your main fuse sets how much power the house can draw at once, and the charger has to share it with the oven, the hot water and everything else. This is why load balancing matters, and why a bigger charger is not always usable on a smaller supply. Our guide to how many amps an EV charger uses covers the sums from 6 A to 32 A.
  3. Its own circuit. Every charger needs its own dedicated circuit and a free space in the fuse box. If the consumer unit is full, the installer may need to add a way, or occasionally do a small upgrade.
  4. Earth-fault protection. The charger circuit needs a residual current device (RCD). A charger without built-in DC fault detection needs a Type B RCD. A charger with built-in 6 mA DC fault detection, such as amina 1 and amina S, works with a Type A RCD. The charger’s datasheet tells the installer which one to fit.
  5. Surge protection. In Norway, the fuse box needs surge protection for a new charger circuit. If it is missing, the electrician adds it.
  6. A notice to the grid company. The electrician tells the local grid company about the new installation and gives you the documentation of the work.
  7. A certified installer. This is fixed electrical work, not a plug-in appliance, so professional installation is a legal requirement across most of Europe and mandatory in Norway. More on finding a good one below.

Choosing the right charger

Three things actually matter: power, connector, and how the charger is managed. The rest is preference.

 

Power. Home chargers come as 7.4 kW, 11 kW or 22 kW. For a single car charged overnight, 7.4 kW is plenty, adding enough range by morning to cover roughly ten times the average daily drive. The higher speeds need three-phase, and it is worth knowing that most electric cars accept a maximum of 11 kW on AC anyway, so a 22 kW charger often cannot be used in full. Our guide to charging speeds has the detail.

 

Connector. In Europe this is Type 2, which every modern EV and plug-in hybrid uses. A fixed, tethered cable is usually the tidiest option at home.

 

Management. This is where our own range splits by need. The amina S is the home unit: up to 22 kW, Zigbee and Bluetooth for smart-home integration, and at about a kilogram one of the lightest and most discreet chargers on the market. The amina C is the same hardware with OCPP added, for a shared car park, a managed setup, or anyone who wants their charger to work with any operator or energy platform rather than a single app. And where charging has to be billed to a certified standard, which is common in the Benelux countries, Finland, Germany and Austria, the amina M is the MID-certified option.

Working with a certified installer

Do not fit it yourself. A good installer assesses your supply, chooses the safest connection point, handles the wiring and protective devices, and leaves you with paperwork confirming the job meets national standards, which matters for both your warranty and your insurance. When you are picking one, look for accreditation specific to EV charging, check they know your national wiring rules and any grant requirements, and get more than one quote.

What happens on the day

A straightforward install is a half-day job. The electrician inspects the consumer unit and plans the cable run, mounts the charger to a wall or post, connects it on its own circuit, then configures and tests it before handing over. Most of the time and cost comes down to how far the cable has to travel and whether the fuse box needs any work.

Before the first bolt is turned, a good installer guide makes all the difference – helping installers deliver safe, reliable home charging every time.

How much does it cost to install an EV charger?

Three things make up the total, and only one of them is known in advance.

 

The charger. This varies by model, power and features, from a simple home unit to a managed or metered one.

 

The installation. The cost moves with local labour rates and with how much work is actually involved.

 

Any electrical upgrade. This is the swing factor. A charger sited near a fuse box with spare capacity is cheap to fit. A long cable run, a full consumer unit, or a supply that needs upgrading can add a fair bit to the bill.

 

The only reliable number is a quote from a certified installer who has seen your setup. Before you get one, check your national scheme: several countries offer grants or tax relief for home charging, particularly for apartments and shared parking, and the terms change often, so your local energy authority is the place to confirm what is currently on offer.

For the price of an amina charger with installation, contact a dealer. You find one on our find a dealer page.

Installation in Norway

These rules apply to a home charger in Norway. Your electrician knows the details and handles the paperwork.

Rule Source
Only a registered electrical company may install a charger. You may not do it yourself. DSB
From January 2023, every new charge point must be a separate, permanently mounted charger. DSB
The charger has its own circuit in the fuse box. NEK 400
Earth-fault protection: a Type B RCD, or a Type A RCD if the charger has built-in 6 mA DC fault detection (RDC-DD), as amina 1 and amina S have. NEK 400, IEC 62955, charger datasheet
Surge protection in the fuse box. NEK 400
The electrician notifies the grid company and documents the work. Your electrician

A standard installation usually includes a new circuit, a limited length of cable, the notice to the grid company and the documentation in Boligmappa. It needs a free space in the fuse box and surge protection. A long cable run, digging or a fuse box upgrade adds to the cost.

Choosing a charger for a home in Norway? Our guide to home EV chargers in Norway compares kW, grid type, rules and installation.

Frequently asked questions

Can I install an EV charger myself?

No. It is fixed electrical work and must be carried out by a certified electrician to meet safety and legal requirements. In Norway this is mandatory, and most of Europe takes the same line.

How long does installation take?

For a professional, a straightforward home install is usually a half-day job. More involved work, such as a fuse-box upgrade or a long cable run, takes longer.

Can I just charge from a normal socket instead?

In an emergency, yes, but not as a daily routine. Household sockets are not built for hours at full load, and in Norway, every new charge point must be a permanently mounted charger from January 2023 (DSB). Our guide to charging from a socket explains why.

Can I have two chargers on the same circuit?

No. Each charger needs its own circuit. For two chargers, for example for two cars, the electrician fits two circuits and checks that the main fuse can carry both. Load balancing can share the available power between the chargers, so the main fuse does not trip.

Which cable does an EV charger need?

The electrician sizes the fixed cable from the fuse box to the charger. The size depends on the charger current, the cable length and how the cable is laid, following the wiring rules (NEK 400 in Norway). The cable to the car is a Type 2 charging cable. amina S and amina C have one built in, and amina 1 has a Type 2 socket for your own cable.

Can I get support for a home charger in Norway?

Yes, as part of a smart energy system. Enova supports a price- and power-controlled energy system for homes, which must control at least two energy loads, for example the electric car and the water heater. The system reads the hourly electricity price and the home’s total use from the HAN port of the electricity meter. The support is 25% of the approved costs, up to NOK 10,000, and you must apply before you start. The conditions are on enova.no (read 11 November 2026).

Is it worth installing a home charger?

If you have somewhere to park and a supply to connect to, yes. It is the cheapest and most convenient way to run an electric car, and the charger will outlast the car you bought it for.

Sources

  • DSB, safe charging of electric cars: dsb.no
  • NEK 400, the Norwegian standard for low-voltage electrical installations
  • IEC 62955, residual direct current detecting devices (RDC-DD) for EV charging
  • Enova, support for a price- and power-controlled energy system (read 11 November 2026): enova.no